Run report — Full CIT
Run:      20260706-070204-EA3-full-cit
Sprint:   2026_S13
Unit:     EA3 / base
Build:    -
Operator: Anais
Status:   finished
Started:  2026-07-06T07:02:04+00:00

Summary:  4 fail, 3 na, 1 pass, 37 skip

Results:
  [FAIL ] MOT-10    Kinematic Calibration
  [FAIL ] MOT-4     Roll around
  [FAIL ] NET-7     Radio Mesh
  [FAIL ] VI-2      Test autonomous rover
  [PASS ] MOT-3     Elbows down / Elbows up
  [NA   ] INT-9     Test Gripper
  [NA   ] MCN-3     Mechanical assembly integrity
  [NA   ] MCN-4     Mechanical assembly tightness
  [SKIP ] FW-4      Latest FW is used   — (early-finish)
  [SKIP ] INT-1     Basic end effector rotation   — (early-finish)
  [SKIP ] INT-12    Test recovery open loop   — (early-finish)
  [SKIP ] INT-13    Test recovery closed loop   — (early-finish)
  [SKIP ] INT-2     Advanced end effector rotation   — (early-finish)
  [SKIP ] INT-3     Valve opening   — (early-finish)
  [SKIP ] INT-4     Reach Single Compass   — (early-finish)
  [SKIP ] INT-5     Reach Double Compass   — (early-finish)
  [SKIP ] INT-6     Reach Rover   — (early-finish)
  [SKIP ] INT-7     Stop motion   — (early-finish)
  [SKIP ] INT-8     Resume motion   — (early-finish)
  [SKIP ] MCN-1     Backbone integrity   — (early-finish)
  [SKIP ] MCT-1     Robot can be turned on from any ON/OFF button   — (early-finish)
  [SKIP ] MCT-2     Robot can be turned off   — (early-finish)
  [SKIP ] MCT-3     Robot can charge   — (early-finish)
  [SKIP ] MCT-4     Robot can go alone   — (early-finish)
  [SKIP ] MCT-5     Temperature monitoring (CPU + motherboard)   — (early-finish)
  [SKIP ] MCT-6     sanity check   — (early-finish)
  [SKIP ] MOT-1     MPC can be started   — (early-finish)
  [SKIP ] MOT-11    stress the Posturing   — (early-finish)
  [SKIP ] MOT-2     Elbows down / Elbows up   — (early-finish)
  [SKIP ] MOT-5     Posturing   — (early-finish)
  [SKIP ] MOT-6     Rolling below an obstacle   — (early-finish)
  [SKIP ] MOT-7     Ground adaptation.   — (early-finish)
  [SKIP ] MOT-8     Walking gait (with rolling)   — (early-finish)
  [SKIP ] MOT-9     Walking Mode   — (early-finish)
  [SKIP ] NET-1     Robot wifi works   — (early-finish)
  [SKIP ] NET-2     Robot wifi connection   — (early-finish)
  [SKIP ] NET-3     SSH connection to the motion PC   — (early-finish)
  [SKIP ] NET-4     Steamdeck can be turned on   — (early-finish)
  [SKIP ] NET-5     Robot modules access via their hostnames   — (early-finish)
  [SKIP ] NET-6     Commander works   — (early-finish)
  [SKIP ] NET-8     Robot can control without internet access in the vision pc   — (early-finish)
  [SKIP ] SW-5      Release image loading   — (early-finish)
  [SKIP ] VI-1      Test vision connectivity   — (early-finish)
  [SKIP ] VI-3      Climbing on an obstacle   — (early-finish)
  [SKIP ] VI-4      Stepping over an obstable   — (early-finish)