Run report — Full CIT · EA7
20260819-155118-EA7-full-cit · sprint 2026_S17 · build main-b0ea34b5cb · operator Cheikh · status finished
8 fail 1 na 31 pass 3 skip
| ID | Element | Verdict | Note & evidence | Ticket |
|---|---|---|---|---|
| MCN-1 | Backbone integrity | fail | https://app.clickup.com/t/4570305/86cb7d5kq | |
| MCN-3 | Mechanical assembly integrity | fail | https://app.clickup.com/t/4570305/86cb7e06k | |
| MCN-4 | Mechanical assembly tightness | fail | https://app.clickup.com/t/4570305/86cb7e06k | |
| MCT-4 | Robot can go alone | fail | https://app.clickup.com/t/4570305/86canre3z | |
| MCT-6 | sanity check | fail | https://app.clickup.com/t/4570305/86cb7d5kq | |
| MOT-1 | MPC can be started | fail | https://app.clickup.com/t/4570305/86canrx57 | |
| MOT-9 | Walking Mode | fail | https://app.clickup.com/t/4570305/86cb7ccq4 | |
| NET-6 | Commander works | fail | https://app.clickup.com/t/4570305/86cb7fn67 | |
| FW-4 | Latest FW is used | pass | — | |
| INT-12 | Test recovery open loop | pass | — | |
| INT-13 | Test recovery closed loop | pass | — | |
| INT-4 | Reach Single Compass | pass | — | |
| INT-6 | Reach Rover | pass | — | |
| INT-7 | Stop motion | pass | — | |
| INT-8 | Resume motion | pass | — | |
| MCT-1 | Robot can be turned on from any ON/OFF button | pass | — | |
| MCT-2 | Robot can be turned off | pass | — | |
| MCT-3 | Robot can charge | pass | — | |
| MCT-5 | Temperature monitoring (CPU + motherboard) | pass | — | |
| MCT-7 | Record Elecstack and Top module UIDs | pass | — | |
| MCT-8 | E-stop halts motion in progress | pass | Robot falls but it currently accpetd | — |
| MOT-11 | stress the Posturing | pass | — | |
| MOT-12 | Rolling in single compass | pass | — | |
| MOT-13 | lift each wheel and landing | pass | — | |
| MOT-14 | Rolling with three wheels | pass | — | |
| MOT-2 | Elbows down / Elbows up | pass | — | |
| MOT-3 | Elbows down / Elbows up | pass | — | |
| MOT-4 | Roll around | pass | — | |
| MOT-5 | Posturing | pass | — | |
| MOT-8 | Walking gait (with rolling) | pass | — | |
| NET-1 | Robot wifi works | pass | — | |
| NET-10 | Robot command restart & launchfiles load without internet (vision PC) | pass | — | |
| NET-2 | Robot wifi connection | pass | — | |
| NET-3 | SSH connection to the motion PC | pass | — | |
| NET-4 | Steamdeck can be turned on | pass | — | |
| NET-5 | Robot modules access via their hostnames | pass | — | |
| NET-8 | Robot can control without internet access in the vision pc | pass | — | |
| SW-5 | Release image loading | pass | — | |
| SW-6 | Check disk/image state | pass | — | |
| INT-9 | Test Gripper | na | — | |
| SW-7 | Fill image store with a fake large image, then watch GC | skip | — | |
| VI-1 | Test vision connectivity | skip | (early-finish) | https://app.clickup.com/t/4570305/86cb7h21e |
| VI-2 | Test autonomous rover | skip | — |